These pipe adapters will allow you to install either the V1 (round) or V2 (square) Starlink antennas on an existing 1 1/2″, 1 5/8″, 2″, or 2 3/8″ OD mast in less than 10 minutes. Saves time & Money by re-using existing mounts and surfaces! Make sure you select the correct adapter as they are NOT interchangeable.
NOTE: Installers and others who aren’t sure what version they are getting or working with, should order the V2 version, as it is currently backwards compatible to V1!
These pipe adapters/pole mount adapters have been modified to work with V1 (round) or V2 (square) Starlink antennas!
We also recommend removing the “dots” from your Starlink mast and using a 1/2″ bolt to secure your Starlink mast to this adapter!
This pipe adapter (a.k.a. pole adapter, mast adapter, mount adapter, pole mount adapter) converts an existing 1 5/8″ or 2″ pipe (a.k.a. pole, mast, mount, etc.) down to the Starlink type of connector used for Starlink antennas!
This pipe adapter is commonly used to install a Starlink antenna on a WildBlue, Exede, Viasat, or other 1 5/8″ or 2″ J-mount, Ground Pole Mount, or another existing mount!
These adapters can be used with our DirecTV 2″ J-mount brackets as long as you use optional support struts to secure the J-mount bracket!
There are many other ways you can install Starlink. Please contact us if you have any questions!
NOTE: Our V2 Adapter for the square Starlink Antenna, also works for V1 round Starlink Antenna! It also works as a 1 1/2″ – 2 3/8″ to 2″ pipe adapter once you remove the top bolts.
We’ve done this so that installers only have to pack around 1 adapter for use with multiple applications and installations. A newer design was released on 4/10/22 that just has 4 holes in the base, but also a longer top piece to accommodate DirecTV, Exede, WildBlue, Viasat, and other 2″ OD applications as well.
Installation:
- Slide pipe adapter over existing 1 5/8″,2″, or 2 3/8 O.D. pipe / pole / mast.
- Tighten Bolts.
If you ordered a V2 adapter, tighten the bolts that secure the Starlink mast into the adapter as well. - Check to make sure the adapter is level in two perpendicular directions.
- Do not overtighten bolts.
Make sure your existing mount is strong enough and supported well enough to support your Starlink antenna even during high winds, snow, etc.
You can purchase and add support struts or guy wires to do so also.
Features:
- Holes for Starlink “dots” for V1 (round) Antennas
- Additional bolts to secure V2 (square) antennas
- Over-pipe design
- The 2″ OD top piece allows this adapter to be used for DirecTV, ViaSat, WildBlue, Exede, and other applications as well!
- Aluminum w/ stainless steel bolts, nuts, etc.
- Weight: 2 lbs.
Contents (V1):
- 6 – 5/16-18 x 1 1/4″ stainless bolts
- 6 – 5/16-18 jam nuts
- aluminum adapter
Contents (V2):
- 6 – 5/16-18 x 1 1/4″ stainless bolts
- 6 – 5/16-18 stainless jam nuts
- 2 – 5/16-18 x 1″ stainless bolts
- 2 – 5/16-18 stainless jam nuts
- aluminum adapter
SPECIAL RETURN POLICY:
Returns and shipments of returns must be pre-approved and then postmarked within 10-days of receipt (per tracking status) of these adapters for refund or exchange. Return and/or Exchange shipping is not included. Also, due to a few people assuming they can just order and use our adapter for a couple of days or weeks until their Starlink Pipe Adapter arrives, and then just return our adapter, we are now charging a 20% restocking fee on returned adapters to help us cover our labor and other costs of the return. Please contact us for information first, or be sure which version of this adapter you are ordering before you place an order! On the bright side, we may be able to offer you a label to ship the adapter to another customer at the new customer’s expense if you happen to order the wrong adapter or if it is no longer legitimately needed! Contact us for info!